Prüfbericht - Produkte Test Report - Products Prüfbericht-Nr.: CN26NHAO 002 Auftrags-Nr.: 168585292 Seite 1 von 22 Test report no.: Order no.: Page 1 of 22 Kunden-Referenz-Nr.: N/A Auftragsdatum: 2025-11-16 Client reference no.: Order date: Odyssey Robot LLC Auftraggeber: Address: 21 Miller Alley Suite210, Pasadena, CA 91103 Client: Prüfgegenstand: Remote Controller Test item: Bezeichnung / Typ-Nr.: YMAWZOD Identification / Type no.: Auftrags-Inhalt: Test Report Order content: Prüfgrundlage: CFR Title 47 FCC Part 15: Subpart C Section 15.247 Test specification: CFR Title 47 FCC Part 15: Subpart C Section 15.209 Wareneingangsdatum: 2025-11-16 Date of sample receipt: Prüfmuster-Nr.: A004155498-001~008 Test sample no: Prüfzeitraum: 2025-11-20 - 2025-12-29 Testing period: Please refer to Photo Document Ort der Prüfung: TÜV Rheinland Place of testing: (Shenzhen) Co., Ltd. Prüflaboratorium: TÜV Rheinland Testing laboratory: (Shenzhen) Co., Ltd. Prüfergebnis*: Pass Test result*: geprüft von: genehmigt von: tested by: authorized by: X X Datum: Ausstellungsdatum: Date: 2026-01-09 Signed by: Bell Hu Issue date: 2026-01-09 Signed by: Jonathan Li Stellung / Position: Sachverständige(r)/Expert Stellung / Position: Sachverständige(r)/Expert Sonstiges / FCC ID: 2BSYT-YMAWZOD Other: This report is for 2.4GHz DTS. Zustand des Prüfgegenstandes bei Anlieferung: Prüfmuster vollständig und unbeschädigt Condition of the test item at delivery: Test item complete and undamaged * Legende: P(ass) = entspricht o.g. Prüfgrundlage(n) F(ail) = entspricht nicht o.g. Prüfgrundlage(n) N/A = nicht anwendbar N/T = nicht getestet * Legend: P(ass) = passed a.m. test specification(s) F(ail) = failed a.m. test specification(s) N/A = not applicable N/T = not tested Dieser Prüfbericht bezieht sich nur auf das o.g. Prüfmuster und darf ohne Genehmigung der Prüfstelle nicht auszugsweise vervielfältigt werden. Dieser Bericht berechtigt nicht zur Verwendung eines Prüfzeichens. This test report only relates to the above mentioned test sample. Without permission of the test center this test report is not permitted to be duplicated in extracts. This test report does not entitle to carry any test mark. TUV Rheinland (Shenzhen) Co., Ltd., 1601-1604, 1801-1804, Tower A Building 2, Shenzhen International Innovation Valley, Dashi 1st Road, Xili Street, Xili Community, Nanshan District, Shenzhen, 518000 Mail: service-gc@tuv.com · Web: www.tuv.com V101023GCNSR Prüfbericht - Produkte Test Report - Products Prüfbericht-Nr.: CN26NHAO 002 Seite 2 von 22 Page 2 of 22 Test report no.: Anmerkungen Remarks 1 Alle eingesetzten Prüfmittel waren zum angegebenen Prüfzeitraum gemäß eines festgelegten Kalibrierungsprogramms unseres Prüfhauses kalibriert. Sie entsprechen den in den Prüfprogrammen hinterlegten Anforderungen. Die Rückverfolgbarkeit der eingesetzten Prüfmittel ist durch die Einhaltung der Regelungen unseres Managementsystems gegeben. Detaillierte Informationen bezüglich Prüfkonditionen, Prüfequipment und Messunsicherheiten sind im Prüflabor vorhanden und können auf Wunsch bereitgestellt werden. The equipment used during the specified testing period was calibrated according to our test laboratory calibration program. The equipment fulfils the requirements included in the relevant standards. The traceability of the test equipment used is ensured by compliance with the regulations of our management system. Detailed information regarding test conditions, equipment and measurement uncertainty is available in the test laboratory and could be provided on request. 2 Wie vertraglich vereinbart, wurde dieses Dokument nur digital unterzeichnet. Der TÜV Rheinland hat nicht überprüft, welche rechtlichen oder sonstigen diesbezüglichen Anforderungen für dieses Dokument gelten. Diese Überprüfung liegt in der Verantwortung des Benutzers dieses Dokuments. Auf Verlangen des Kunden kann der TÜV Rheinland die Gültigkeit der digitalen Signatur durch ein gesondertes Dokument bestätigen. Diese Anfrage ist an unseren Vertrieb zu richten. Eine Umweltgebühr für einen solchen zusätzlichen Service wird erhoben. Informationen zur Verifizierung der Authentizität unserer Dokumente erhalten Sie auf folgender Webseite: go.tuv.com/digital-signature As contractually agreed, this document has been signed digitally only. TUV Rheinland has not verified and unable to verify which legal or other pertaining requirements are applicable for this document. Such verification is within the responsibility of the user of this document. Upon request by its client, TUV Rheinland can confirm the validity of the digital signature by a separate document. Such request shall be addressed to our Sales department. An environmental fee for such additional service will be charged. For information on verifying the authenticity of our documents, please visit the following website: go.tuv.com/digital-signature 3 Prüfklausel mit der Note * wurden an qualifizierte Unterauftragnehmer vergeben und sind unter der jeweiligen Prüfklausel des Berichts beschrieben. Abweichungen von Prüfspezifikation(en) oder Kundenanforderungen sind in der jeweiligen Prüfklausel im Bericht aufgeführt. Test clauses with remark of * are subcontracted to qualified subcontractors and descripted under the respective test clause in the report. Deviations of testing specification(s) or customer requirements are listed in specific test clause in the report. 4 Die Entscheidungsregel für Konformitätserklärungen basierend auf numerischen Messergebnisen in diesem Prüfbericht basiert auf der "Null-Grenzwert-Regel" und der "Einfachen Akzeptanz" gemäß ILAC G8:2019 und IEC Guide 115:2021, es sei denn, in der auf Seite 1 dieses Berichts genannten angewandten Norm ist etwas anderes festgelegt oder vom Kunden gewünscht. Dies bedeutet, dass die Messunsicherheit nicht berücksichtigt wird und daher auch nicht im Prüfbericht angegeben wird. Zu weiteren Informationen bezueglich des Risikos durch diese Entscheidungsregel siehe ILAC G8:2019. The decision rule for statements of conformity, based on numerical measurement results, in this test report is based on the “Zero Guard Band Rule” and “Simple Acceptance” in accordance with ILAC G8:2019 and IEC Guide 115:2021, unless otherwise specified in the applied standard mentioned on Page 1 of this report or requested by the customer. This means that measurement uncertainty is not taken in account and hence also not declared in the test report. For additional information to the resulting risk based of this decision rule please refer to ILAC G8:2019. Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 3 von 22 Test Report No.: Page 3 of 22 Test Summary 5.1.1 ANTENNA REQUIREMENT RESULT: Pass 5.1.2 MAXIMUM CONDUCTED OUTPUT POWER RESULT: Pass 5.1.3 CONDUCTED POWER SPECTRAL DENSITY RESULT: Pass 5.1.4 6DB BANDWIDTH RESULT: Pass 5.1.5 99% BANDWIDTH RESULT: Pass 5.1.6 CONDUCTED SPURIOUS EMISSIONS MEASURED IN 100 KHZ BANDWIDTH RESULT: Pass 5.1.7 RADIATED SPURIOUS EMISSION RESULT: Pass Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 4 von 22 Test Report No.: Page 4 of 22 Contents 1GENERAL REMARKS ..........................................................................................................................5 1.1 COMPLEMENTARY MATERIALS............................................................................................................5 2TEST SITES........................................................................................................................................6 2.1 TEST FACILITIES ................................................................................................................................6 2.2 LIST OF TEST AND MEASUREMENT INSTRUMENTS ................................................................................7 2.3 TRACEABILITY ...................................................................................................................................8 2.4 CALIBRATION.....................................................................................................................................8 2.5 MEASUREMENT UNCERTAINTY............................................................................................................9 2.6 LOCATION OF ORIGINAL DATA ............................................................................................................9 2.7 STATUS OF FACILITY USED FOR TESTING ............................................................................................9 3GENERAL PRODUCT INFORMATION ...................................................................................................10 3.1 PRODUCT FUNCTION AND INTENDED USE ..........................................................................................10 3.2 RATINGS AND SYSTEM DETAILS........................................................................................................10 3.3 INDEPENDENT OPERATION MODES....................................................................................................11 3.4 NOISE GENERATING AND NOISE SUPPRESSING PARTS ......................................................................11 3.5 SUBMITTED DOCUMENTS..................................................................................................................11 4TEST SET-UP AND OPERATION MODES..............................................................................................12 4.1 PRINCIPLE OF CONFIGURATION SELECTION .......................................................................................12 4.2 TEST OPERATION AND TEST SOFTWARE ...........................................................................................12 4.3 SPECIAL ACCESSORIES AND AUXILIARY EQUIPMENT .........................................................................12 4.4 COUNTERMEASURES TO ACHIEVE EMC COMPLIANCE .......................................................................12 4.5 TEST SETUP DIAGRAM .....................................................................................................................13 5TEST RESULTS ................................................................................................................................14 5.1 TRANSMITTER REQUIREMENT & TEST SUITES....................................................................................14 5.1.1 Antenna Requirement................................................................................................................14 5.1.2 Maximum Conducted Output Power..........................................................................................15 5.1.3 Conducted Power Spectral Density...........................................................................................16 5.1.4 6dB Bandwidth ..........................................................................................................................17 5.1.5 99% Bandwidth..........................................................................................................................18 5.1.6 Conducted Spurious Emissions Measured in 100 kHz Bandwidth............................................19 5.1.7 Radiated Spurious Emission .....................................................................................................20 6PHOTOGRAPHS OF THE TEST SET-UP ...............................................................................................21 7LIST OF TABLES...............................................................................................................................22 Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 5 von 22 Test Report No.: Page 5 of 22 1 General Remarks 1.1 Complementary Materials All attachments are integral parts of this test report. This applies especially to the following appendix: Appendix A: Photographs of the Test Set-up. Appendix B: Test Results of 2.4GHz Band Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 6 von 22 Test Report No.: Page 6 of 22 2 Test Sites 2.1 Test Facilities TÜV Rheinland (Shenzhen) Co., Ltd. 2-3F, 101 & 102, No.2, Nuclear Power Industrial Park, Fuming Community, Fucheng Street, Longhua District, Shenzhen 518000, People’s Republic of China FCC Accreditation Designation No.: 694916 ISED wireless device testing laboratory: 25069 Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 7 von 22 Test Report No.: Page 7 of 22 2.2 List of Test and Measurement Instruments Table 1: List of Test and Measurement Equipment Radio Spectrum Testing (Band-Tonscend) Equipment Manufacturer Model Serial No. Cal. Date Cal. until EXA Signal Analyzer, Multi- Keysight N9010B MY60241175 23.09.2025 22.09.2026 touch MXG X-Series RF Vector Signal Keysight N5182B MY61250137 23.09.2025 22.09.2026 Generator EXG X-Series Microwave Analog Keysight N5173B MY61250141 23.09.2025 22.09.2026 Signal Generator DC Power Supply Keysight E3642A MY61276100 23.09.2025 22.09.2026 Wireless R&S CMW270 102505 23.09.2025 22.09.2026 Connectivity Tester Power Control Unit Tonscend JS0806-4ADC N/A 23.09.2025 22.09.2026 Automation Control Tonscend JS0806-2 21C8060396 23.09.2025 22.09.2026 Unit Test Software Tonscend JS1120-3 N/A N/A N/A Control PC Lenovo TianYi510S-071MB YLX23JMF N/A N/A Humid & Temp Programmable BOST NTH090-60 19040801 25.02.2025 24.02.2026 Tester Unwanted Emission Testing (TS9975) Equipment Manufacturer Model Serial No. Cal. Date Cal. until EMI Test Receiver R&S ESR 7 102021 22.09.2025 21.09.2026 Signal Analyzer R&S FSV 40 101439 22.09.2025 21.09.2026 System Controller R&S SCI-100 S10010038 N/A N/A Interface Filterbank R&S Wlan 100759 22.09.2025 21.09.2026 OSP R&S OSP 120102040 N/A N/A Pre-amplifier R&S SCU08F1 08320031 22.09.2025 21.09.2026 Amplifier R&S SCU-18F 180070 22.09.2025 21.09.2026 Amplifier R&S SCU40A 100475 22.09.2025 21.09.2026 Trilog Broadband Antenna Schwarzbeck VULB 9162 193 28.09.2024 27.09.2026 (30 MHz - 7 GHz) Double-Ridged Antenna (1 -18 ETS-LINDGREN 3117 00218717 28.09.2024 27.09.2026 GHz) Wideband Ridged Horn Antenna (18- Steatite QMS-00880 19067 28.09.2024 27.09.2026 40 GHz) Active Loop Schwarzbeck FMZB 1513 302 28.09.2024 27.09.2026 Antenna EMC32 Test software R&S N/A N/A N/A (V10.60.10) Control PC Dell OptiPlex 7050 36NV9P2 N/A N/A 3m Semi-Anechoic APC17151- Albatross SAC-3m 14.09.2024 13.09.2027 Chamber SAC Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 8 von 22 Test Report No.: Page 8 of 22 2.3 Traceability All measurement equipment calibrations are traceable to NIM (National Institute of Metrology) or where calibration is performed in other countries, to equivalent nationally recognized standards organizations. 2.4 Calibration Equipment requiring calibration is calibrated periodically by the manufacturer or according to manufacturer’s specifications. Additionally all equipment is verified for proper performance on a regular basics using in house standards or comparisons. Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 9 von 22 Test Report No.: Page 9 of 22 2.5 Measurement Uncertainty The estimated combined standard uncertainty for radiated emissions and conducted emissions measurements as below table. Table 2: Measurement Uncertainty Parameter Uncertainty (k=2) RF output power, conducted ± 0.99 dB Occupied Channel Bandwidth ± 2.08 % RF power density, conducted ± 0.99 dB Unwanted Emissions, conducted ± 0.89 dB All emissions, radiated ± 4.17 dB 2.6 Location of Original Data The original copies of all test data taken during actual testing were attached at Appendix A & B of this report and delivered to the applicant. A copy has been retained in the TÜV Rheinland (Shenzhen) file for certification follow-up purposes. 2.7 Status of Facility Used for Testing The TÜV Rheinland (Shenzhen) Co., Ltd. Test facility located at 2-3F, 101 & 102, No.2, Nuclear Power Industrial Park, Fuming Community, Fucheng Street, Longhua District, Shenzhen 518000, People’s Republic of China. is listed on the US Federal Communications Commission list of facilities approved to perform measurements. Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 10 von 22 Test Report No.: Page 10 of 22 3 General Product Information 3.1 Product Function and Intended Use The EUT (Equipment Under Test) is Remote Controller. It supports 2.4GHz Band and 5.8GHz Band. For details refer to the User Manual, Technical Description and Circuit Diagram. 3.2 Ratings and System Details Table 3: Technical Specification of EUT General Information of EUT Value Kind of Equipment Remote Controller Type Designation YMAWZOD FCC ID 2BSYT-YMAWZOD AC 100-240V, 50/60Hz input via AC/DC adapter` Operating Voltage or Battery operated (DC 3.6V) Testing Voltage AC 120V, 60Hz or Built-in battery Operating Temperature -10°C ~ 40 °C Range Radiofrequency operating 1) 2.4GHz Band: operating within 2400-2483.5MHz mode 2) 5.8GHz Band: operating within 5725-5850MHz Technical Specification of 2.4GHz Band Operating Frequency 2407.48-2463.48MHz for 1.4MHz Bandwidth 2411.48-2459.48MHz for 3MHz Bandwidth 2414.48-2459.48MHz for 5MHz Bandwidth 2408.48-2466.48MHz for 10MHz Bandwidth 2414.48-2460.48MHz for 20MHz Bandwidth 2424.48-2450.48MHz for 40MHz Bandwidth Type of Modulation OFDM Channel Number 29 channels for 1.4MHz Bandwidth 17 channels for 3MHz Bandwidth 10 channels for 5MHz Bandwidth 59 channels for 10MHz Bandwidth 47 channels for 20MHz Bandwidth 27 channels for 40MHz Bandwidth Antenna Type Integral Antennas Antenna Number 1Tx1Rx for SISO mode (ANT1 or ANT2) 2Tx2Rx for MIMO mode (ANT1+ANT2, Completely uncorrelated signals) Antenna Gain 2.9 dBi for ANT1/2(Provided by the Client) The type of wideband data DTS transmission equipment: Note: The correctness of all data provided by customer in the test report is ensured and responsible of the customer. Any misjudgment of the test results caused by the use of incorrect data provided by customer shall be borne by the customer. Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 11 von 22 Test Report No.: Page 11 of 22 3.3 Independent Operation Modes The basic operation modes are: A. On, 2.4GHz Band wireless transmitting mode 1) Low Channel 2) Middle Channel 3) High Channel B. Off 3.4 Noise Generating and Noise Suppressing Parts Refer to Circuit Diagram for further details. 3.5 Submitted Documents - Application Form - User Manual - ID Label and Location Info - Operation Description Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 12 von 22 Test Report No.: Page 12 of 22 4 Test Set-up and Operation Modes 4.1 Principle of Configuration Selection Radio Spectrum: The equipment under test (EUT) was configured at its highest power output in order to measure its highest possible radiation and conducted level. The test modes were adapted accordingly in reference to the instructions for use. Emission: The equipment under test (EUT) was configured to measure its highest possible radiation level. The test modes were adapted accordingly in reference to the instructions for use. 4.2 Test Operation and Test Software Test operation refers to test setup in chapter 5. All testing were performed according to the procedures in ANSI C63.10-2020. 4.3 Special Accessories and Auxiliary Equipment Table 4: List of Accessories and Auxiliary Equipment Description Manufacturer Model S/N Rating Laptop Lenovo T480 PF-16A6N8 / Shenzhen HONOR AC/DC adapter PD-65US1 -- -- ELECTRONIC CO 4.4 Countermeasures to Achieve EMC Compliance The test sample which has been tested contained the noise suppression parts as described in the Technical Construction File (TCF). No additional measures were employed to achieve compliance. Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 13 von 22 Test Report No.: Page 13 of 22 4.5 Test Setup Diagram Diagram of Measurement Configuration for Radiation Test (Below 1GHz) Diagram of Measurement Configuration for Radiation Test (Above 1GHz) Diagram of Measurement Configuration for Conducted Transmitter Measurement Diagram of Measurement Configuration for Mains Conduction Measurement Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 14 von 22 Test Report No.: Page 14 of 22 5 Test Results 5.1 Transmitter Requirement & Test Suites 5.1.1 Antenna Requirement RESULT: Pass Test Specification Test standard : FCC Part 15.247(b)(4) and Part 15.203 the use of antennas with directional gains that do not Limit : exceed 6 dBi According to the manufacturer declared, the EUT have Integral Antennas, permanent attachment and no consideration of replacement, refer to section 3.2 for details. Therefore the EUT is considered sufficient to comply with the provision. Refer to EUT Photo for further details. Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 15 von 22 Test Report No.: Page 15 of 22 5.1.2 Maximum Conducted Output Power RESULT: Pass Test Specification Test standard : FCC Part 15.247(b)(3) Basic standard : ANSI C63.10-2020 Limits : < 1 W (Maximum Conducted Power) Kind of test site : Shielded Room Test Setup Date of testing : 2025-11-20 - 2025-12-28 Input voltage : DC 3.6V by battery Operation mode : A Test channel : Low / Middle / High Ambient temperature : 25 ℃ Relative humidity : 45 % Atmospheric pressure : 101 kPa For details refer to following test result. Table 5: Test Result of Maximum Conducted Output Power, 2.4GHz Band Both SISO and MIMO tested, only the worst-case mode (MIMO) was reported. TestMode Frequency (MHz) Result[dBm] Result[W] Limit[W] Verdict 2407.48 24.30 0.2692 < 1.0PASS 1.4MHz 2437.48 24.17 0.2612 < 1.0PASS 2463.48 24.37 0.2735 < 1.0PASS 2411.48 27.08 0.5105 < 1.0PASS 3MHz 2435.48 26.95 0.4955 < 1.0PASS 2459.48 26.71 0.4688 < 1.0PASS 2414.48 27.04 0.5058 < 1.0PASS 5MHz 2434.48 26.61 0.4581 < 1.0PASS 2459.48 26.89 0.4887 < 1.0PASS 2408.48 22.63 0.1832 < 1.0PASS 2437.48 27.69 0.5875 < 1.0PASS 10MHz 2455.48 24.88 0.3076 < 1.0PASS 2466.48 19.58 0.0908 < 1.0PASS 2414.48 20.21 0.1050 < 1.0PASS 2425.48 24.18 0.2618 < 1.0PASS 20MHz 2437.48 27.76 0.5970 < 1.0PASS 2439.48 24.65 0.2917 < 1.0PASS 2460.48 16.40 0.0437 < 1.0PASS 2424.48 14.07 0.0255 < 1.0PASS 2430.48 16.76 0.0474 < 1.0PASS 2431.48 17.78 0.0600 < 1.0PASS 40MHz 2437.48 21.04 0.1271 < 1.0PASS 2439.48 18.33 0.0681 < 1.0PASS 2440.48 15.63 0.0366 < 1.0PASS 2450.48 13.15 0.0207 < 1.0PASS 1) The cable loss is taken into account in results, e.i.r.p.=P(power)+ G 2) Antenna gain(G) of 2.4GHz Band: 2.9dBi Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 16 von 22 Test Report No.: Page 16 of 22 5.1.3 Conducted Power Spectral Density RESULT: Pass Test Specification Test standard : FCC Part 15.247(e) Basic standard : ANSI C63.10-2020 Limits : 8 dBm / 3kHz Kind of test site : Shielded Room Test Setup Date of testing : 2025-11-20 - 2025-12-28 Input voltage : DC 3.6V by battery Operation mode : A Test channel : Low / Middle / High Ambient temperature : 25 ℃ Relative humidity : 45 % Atmospheric pressure : 101 kPa For the measurement records, refer to the appendix B Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 17 von 22 Test Report No.: Page 17 of 22 5.1.4 6dB Bandwidth RESULT: Pass Test Specification Test standard : FCC Part 15.247(a)(2) Basic standard : ANSI C63.10-2020 Limits : > 500 kHz Kind of test site : Shielded Room Test Setup Date of testing : 2025-11-20 - 2025-12-28 Input voltage : DC 3.6V by battery Operation mode : A Test channel : Low / Middle / High Ambient temperature : 25 ℃ Relative humidity : 45 % Atmospheric pressure : 101 kPa For the measurement records, refer to the appendix B Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 18 von 22 Test Report No.: Page 18 of 22 5.1.5 99% Bandwidth RESULT: Pass Test Specification Test standard : FCC Part 15.247(a) Basic standard : ANSI C63.10-2020 Kind of test site : Shielded Room Test Setup Date of testing : 2025-11-20 - 2025-12-28 Input voltage : DC 3.6V by battery Operation mode : A Test channel : Low / Middle / High Ambient temperature : 25 ℃ Relative humidity : 45 % Atmospheric pressure : 101 kPa For the measurement records, refer to the appendix B Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 19 von 22 Test Report No.: Page 19 of 22 5.1.6 Conducted Spurious Emissions Measured in 100 kHz Bandwidth RESULT: Pass Test Specification Test standard : FCC Part 15.247(d) Basic standard : ANSI C63.10-2020 Limits : For Compliance with the peak conducted power limits: 20dB (below that in the 100kHz bandwidth within the band that contains the highest level of the desired power); For Compliance with the conducted power limits: 30dB (below that in the 100kHz bandwidth within the band that contains the highest level of the desired power); In addition, radiated emissions which fall in the restricted bands, must also comply with the radiated emission limits specified in 15.209(a) Kind of test site : Shielded Room Test Setup Date of testing : 2025-11-20 - 2025-12-28 Input voltage : DC 3.6V by battery Operation mode : A Test channel : Low / Middle / High Ambient temperature : 25 ℃ Relative humidity : 45 % Atmospheric pressure : 101 kPa Test results of 100kHz Bandwidth of Frequency Band Edge by Conducted method refer to test plots, and compliance is achieved as well. For the measurement records, refer to the appendix A Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 20 von 22 Test Report No.: Page 20 of 22 5.1.7 Radiated Spurious Emission RESULT: Pass Test Specification Test standard : FCC Part 15.247(d) & FCC Part 15.205 Basic standard : ANSI C63.10-2020 Limits : Refer to 15.209(a) of FCC part 15.247(d) Kind of test site : 3m Semi-anechoic Chamber Test Setup Date of testing : 2025-11-20 - 2025-12-28 Input voltage : DC 3.6V by battery Operation mode : A Test channel : Low / Middle / High Ambient temperature : Refer to test result Relative humidity : Refer to test result Atmospheric pressure : 101 kPa Remark: Testing was carried out within frequency range 9kHz to the tenth harmonics. Only the worst case spurious emissions configuration of the each mode were reported. For the measurement records, refer to the appendix B Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 21 von 22 Test Report No.: Page 21 of 22 6 Photographs of the Test Set-Up For photographs of the test set-up, refer to the appendix A. Prüfbericht - Produkte Test Report - Products Prüfbericht - Nr.: CN26NHAO 002 Seite 22 von 22 Test Report No.: Page 22 of 22 7 List of Tables Table 1: List of Test and Measurement Equipment.......................................................................7 Table 2: Measurement Uncertainty ...............................................................................................9 Table 3: Technical Specification of EUT......................................................................................10 Table 4: List of Accessories and Auxiliary Equipment.................................................................12 Table 5: Test Result of Maximum Conducted Output Power, 2.4GHz Band...............................15