*Pages 1--31 from Microsoft Word - 33819* Federal Communications Commission FCC 03- 289 Before the Federal Communications Commission Washington, D. C. 20554 In the matter of Establishment of an Interference Temperature Metric to Quantify and Manage Interference and to Expand Available Unlicensed Operation in Certain Fixed, Mobile and Satellite Frequency Bands ) ) ) ) ) ) ) ET Docket No. 03- 237 NOTICE OF INQUIRY AND NOTICE OF PROPOSED RULEMAKING Adopted: November 13, 2003 Released: November 28, 2003 Comment Date: [75 days from publication in the Federal Register] Reply Comment Date: [105 days from publication in the Federal Register] By the Commission: Chairman Powell and Commissioner Copps issuing separate statements. Commissioner Adelstein approving in part, concurring in part and issuing a separate statement. INTRODUCTION 1. By this action, the Commission seeks comment on a new “interference temperature” model for quantifying and managing interference. This new concept could shift the current method for assessing interference which is based on transmitter operations, to an approach that is based on the actual radiofrequency (RF) environment, taking into account the interactions between transmitters and receivers. The interference temperature model could represent a fundamental paradigm shift in the Commission’s approach to spectrum management by specifying a potentially more accurate measure of interference that takes into account the cumulative effects of all undesired RF energy, i. e., energy that may result in interference from both transmitters and noise sources, that is present at a receiver at any instant of time. This new approach could provide radio service licensees with greater certainty regarding the maximum permissible interference, and greater protections against harmful interference that could be present in the frequency bands in which they operate. In addition, to the extent that the interference temperature limit in a band is not reached, there could be opportunities for other transmitters, whether licensed or unlicensed, to operate in the band at higher power levels than are currently authorized. In such cases, the interference temperature limit for the band would serve as an upper bound or “cap” on the potential RF energy that could be introduced into the band. We therefore seek comment on the potential of this new approach to interference control and management to promote more efficient use of the spectrum and to possibly create opportunities for new and additional use of radio communications by the American public. 2. The interference temperature concepts introduced in this proceeding were initially developed as part of the Commission’s Spectrum Policy Task Force’s (Task Force) work on means for improving the management of the radio spectrum to increase the public benefits derived from use of the spectrum resource. 1 In its Report, the Task Force observed that interference management has become more 1 See Spectrum Policy Task Force Report (Task Force Report), ET Docket No. 02- 135, November 15, 2002, at p. 1. On November 25, 2002, the Commission issued a public notice FCC 02- 322, inviting public comment on 1 Federal Communications Commission FCC 03- 289 2 difficult because of the greater density, mobility, and variability of RF transmitters and because users have been granted increased flexibility in using the spectrum. 2 The Task Force presented several recommendations for improving interference management in this changed environment, one of which was for the Commission, as a long term strategy, to shift its paradigm for assessing interference towards an approach that uses real- time adaptation based on actual RF environments, and in particular to adopt a new “interference temperature” metric to quantify and manage interference. 3 In response to the Task Force Report, a number of parties expressed general support for further analysis and study of the interference temperature concept. 4 Other parties oppose the interference temperature concept as impractical and unworkable. 5 We further note that the Commission’s Technical Advisory Committee has concluded that introduction of the interference temperature concept is a reasonable approach to defining harmful interference as a function of how the spectrum is actually being used and the designs and margins of particular receivers. 6 3. In the Notice of Inquiry (Inquiry) phase of this proceeding, we are requesting comment, information, and research on a number of issues relating to the development and use of the interference temperature metric and for managing a possible transition from the current transmitter- based approach for interference management to the new interference temperature paradigm. In particular, we are posing questions concerning the development of the interference temperature metric, including the determination of interference temperature limits for specific frequency bands, and an assessment of the cumulative noise and interference environment in radiofrequency bands, including standard methodologies for making assessments, to support the selection of those limits. We are also requesting responses on issues concerning the process that would be involved in possible transitioning to the new interference control methods in the various frequency bands. 4. A general implementation of the interference temperature approach would involve planning, study of existing RF noise and interference levels and other factors, and transition processes that would take a substantial amount of time to complete. We seek comment on several steps we could possibly take prior to a general implementation that would bring elements of this new paradigm into use in the near term and thereby provide a test bed for this model that can be studied and evaluated before any broader the Task Force report. Twenty- eight parties filed comments specifically addressing the issue of the interference temperature concept. 2 Id. at 25- 27. 3 The Task Force’s other principal recommendation for improving interference management was for the Commission to incorporate receiver interference immunity performance into its spectrum policies. Task Force Report, at 31. Pursuant to that recommendation, the Commission recently adopted a Notice of Inquiry (Inquiry) in a related proceeding to begin consideration of incorporation of receiver interference performance specifications into its spectrum policy on a broader basis. See Notice of Inquiry in ET Docket No. 03- 65, adopted March 13, 2003, FCC 03- 54 (released March 24, 2003). In that Inquiry, the Commission observed that if the receivers used with a radio service are designed to provide a certain degree of immunity to, or tolerance of, undesired RF energy and signals, more efficient and predictable use of the spectrum can be achieved, as well as greater opportunities for access to the spectrum. It asked for comment, information and research on a wide range of issues concerning the interference immunity performance capabilities of existing receivers, possibilities for improving the level of receiver interference immunity in the various radio services, possible approaches by which desired levels of performance could be achieved, and the potential positive and negative impacts of receiver standards on innovation and the marketplace. 4 See National Association for Amateur Radio (ARRL) comments at 8, Agilent Technologies, Inc. comments at 7, HYPRES, Inc. comments at 3- 4, Motorola comments at 14, and Wireless Communications Association International, Inc. comments at 10- 12. 5 See Agere comments at 6, AT& T comments at 12- 14, Cingular comments at 18- 19, and Verizon Wireless comments at 10- 12. 6 See Report of the Second Meeting of the FCC Technological Advisory Council III held on July 7, 2003 at http:// www. fcc. gov/ oet/ tac/. 2 Federal Communications Commission FCC 03- 289 3 implementation is considered. Therefore, in the instant Notice of Proposed Rule Making (NPRM) phase, we seek comment on technical rules that would establish interference temperature limits and procedures for assessing the interference temperature in specific frequency bands used by fixed satellite uplinks and by terrestrial fixed point- to- point links. We seek comment on whether the operating circumstances of these facilities would allow for simple and reliable measurement of the interference temperature at a variety of receive sites under diverse situations and circumstances. If we ultimately adopt new technical rules, we seek comment on whether unlicensed devices should be allowed to operate at higher power levels than currently allowed by the rules, so long as they do not cause the interference temperature to exceed the established limits. BACKGROUND 5. The Commission’s policies and rules for managing the radio spectrum, including its efforts to promote spectrum efficiency, traditionally have relied principally on approaches that manage interference by controlling the emissions and locations of transmitters and the frequencies used by specific types of radio operations. Under this model, the Commission has established operational parameters in portions of the spectrum in which the patterns of radio signals, both geographically and technically, are well understood and generally predictable by equipment manufacturers and licensees. In the past, this model generally served well to control interference and to facilitate effective use of the spectrum in environments in which the specific services and operating technology were stable and well defined. However, the dramatic increases in the overall demand for spectrum based services, rapid technical advances in radio systems, in particular the introduction of various advanced modulation technologies, the increased use of spectrum for mobile services, and the need for increased access to the limited supply of spectrum in recent years are straining the effectiveness of the Commission’s longstanding spectrum policies in dealing with some allocations and applications. 7 6. These changes are prompting the Commission to revisit its traditional model and evolve its spectrum management policies to consider more flexible and market- oriented approaches that can provide incentives for users to migrate to more technologically innovative and economically efficient uses of the spectrum. We need to provide opportunities for an ever increasing array of new digital radio technologies and services and to allow licensees to implement and modify these new technologies and services in accordance with the demands of market forces without having to wait for the completion of lengthy ad hoc rule makings or resolution of individual proceedings that hinge on disputes over interference. To meet these needs, we have implemented new licensing schemes under which bands of spectrum are assigned to licensees on a geographic basis and those licensees are provided flexibility to determine the type of services and the technologies and technical implementation designs used to provide those services. The primary restrictions we apply to technical operations under these licenses are those necessary to ensure that interference is not caused to services operating in adjacent geographic areas or in adjacent or nearby frequency bands. These restrictions typically take the form of limits on signal strength at the edge of a licensee’s service area and limits on maximum transmitter power, antenna height and out-of- band emissions. These restrictions, in turn, tend to convey certain rights on the other neighboring or nearby licensees which are protected by such rules. 7. To address the challenges of managing interference in radio environments that are increasingly being characterized by flexible service offerings with a multitude of signal waveforms and by high densities of low power RF transmitters with small signal ranges, the Task Force recommended that, as a long term strategy, where feasible, the Commission shift its paradigm for assessing interference to an approach that uses real- time measurements of actual spectrum use and adapt the responses of transmitters and receivers to these measurements. 8 It observed that quantitative standards reflecting real- 7 Task Force Report at 11- 15. 8 Id at 27. 3 Federal Communications Commission FCC 03- 289 4 time spectrum use would provide users with more certainty and, at the same time, would facilitate enforcement. Noting that it is the ability of a receiver to select and receive a particular signal that determines whether a signal has been degraded by interference, the Task Force stated that the environment in which a receiver operates should be considered, i. e., RF power generated by transmitters and RF noise sources that is present at the receiver. It further stated that the Commission’s rules should specify a more accurate measure of interference that takes into account all the undesired RF energy available to be captured by a particular receiving antenna. To achieve this objective and provide for transition of interference management to more accurate real- time measurements, the Task Force recommended that the Commission adopt a new “interference temperature” metric to quantify and manage interference. To obtain data on the condition of the RF environment in each frequency band that would be used in setting temperature limits, the Task Force recommended that the Commission undertake a systematic study of the RF noise floor. It further recommended that the Commission adopt a standard methodology for measuring the noise floor and create a public/ private partnership for a long- term noise (interference temperature) monitoring network and for the archiving of data, for use by the FCC and the public. Finally, the Task Force recommended that the Commission consider the use of receiver standards, especially voluntary standards, to further address interference, 9 and a NOI released earlier this year by the Commission considers the likely costs and benefits of this potential tool for interference management. 10 The Commission’s consideration of an interference temperature is another step in this ongoing effort to develop a comprehensive and effective approach to interference management. DISCUSSION 8. As part of our efforts to revise our spectrum management policies to address the changes in RF operations and environments that have occurred in recent years, we are now investigating alternative approaches for managing interference. We seek comment on whether it would be necessary to shift our current paradigm for assessing interference from approaches based primarily on transmitter operations towards new approaches that focus on the actual RF environment and interaction between transmitters and receivers, such as the interference temperature metric. 11 Such new approaches could better allow the Commission to enable future uses of the spectrum, while possibly providing a greater degree of certainty to incumbents regarding the RF environment in which they will continue to operate. In the Inquiry portion of the discussion that follows, we first present a description of the interference temperature concept and how interference temperature limits could be used to manage interference. We then discuss and request comment, information, and research on issues relating to possible approaches for a general implementation of interference temperature limits, including questions concerning the development and implementation of the interference temperature metric, the means and criteria by which devices would comply with the interference temperature limits to provide real- time interference protection to licensed services, and methodologies for measuring the cumulative “background noise” and RF interfering signal levels in specific frequency bands and across the radio spectrum. In order to begin our exploration of the process that would be involved in a transition to an interference temperature regime, we seek comment on specific technical guidelines in the NPRM portion of our discussion that could be implemented in the near future for selected frequency bands prior to any possible general implementation of interference temperature limits and real- time adaptation of transmitters to the interference temperature environment. 9. We seek comment on whether the Commission’s approach for managing interference should be changed from its current methodology in order to address the changes in spectrum demand and RF operations and environments that have occurred in recent years. The Task Force Report recommended 9 Id. at 31. 10 See Interference Immunity Performance Specifications for Radio Receivers, ET Docket No. 03- 65, 18 FCC Rcd 6039 (2003). 11 As recommended by the Task Force at 27. 4 Federal Communications Commission FCC 03- 289 5 that the Commission evolve its spectrum policy toward more flexible and market- oriented spectrum policies that will provide incentives for users to migrate to more technologically innovative and economically efficient uses of spectrum. 12 Although no single regulatory model can or should be applied to all spectrum to achieve these goals, the Task Force Report highlighted certain key elements. One such element is the provision of maximum feasible flexibility of spectrum use by both licensed and unlicensed users, subject only to those rules that are necessary to afford reasonable opportunities for access by other spectrum users and to prevent or limit interference among multiple spectrum uses. 13 We seek comment on whether unrealized opportunities exist for unlicensed, low- power users to access spectrum, and whether changes to the Commission’s approach for managing interference would enhance access to the spectrum by such users. We also seek comment on whether changes to the present method of interference management would reduce uncertainty that may exist for current licensees in terms of how much interference they will experience in their bands. A. Notice of Inquiry 10. The Interference Temperature Metric and Interference Management. For purposes of this new interference management paradigm, we define interference temperature as a measure of the RF power generated by undesired emitters plus noise sources that are present in a receiver system (I+ N) per unit of bandwidth. 14 More specifically, it is the temperature equivalent of this power measured in units of “Kelvin” (K). 15 The emissions from undesired transmitters could include out- of- band emissions from transmitters operating on adjacent frequencies or in adjacent frequency bands as well as from transmitters operating on the same frequency as the desired transmitter. In principle, interference temperature measurements would be taken at various receiver locations and these measurements would be combined to estimate the real- time condition of the RF environment. The degree of certainty of the estimates would depend on such factors as the transmitter signal ranges, the uniformity of signal levels over an area, the density and location of temperature measuring devices and the sharing of the data taken by nearby devices; e. g., through “ad hoc cooperative wireless networks.” Measuring devices could be designed with features that include or exclude the energy contributions of particular signals with known characteristics; for example, the emissions of operations licensed to use the subject spectrum in a given geographic area. 11. For an interference temperature limit to function effectively on an adaptive or real- time basis, a system would be needed to measure the interference temperature in the band and communicate that information to devices subject to the limit, and a response process would also be needed to restrict the operation of devices so as to maintain the interference temperature at or below the level of the limit. In the simplest case, the entire process would take place within an individual device. That is, the device 12 Task Force Report at 15. 13 Id. Parties have expressed a desire for flexibility and for certainty regarding operating environment. See Report of the Spectrum Rights and Responsibilities Working Group, Spectrum Policy Task Force at 27. 14 The concept of an interference temperature as a measure of the undesired RF power in a particular band and location is essentially the same as the concept of an “antenna temperature” as described by Wolfram Research. See, for example, Wolfram Research at http:// scienceworld. wolfram. com/ physics/ AntennaTemperature. html. Under this concept, antenna temperature is a component of the total noise temperature of a receiver system, which also includes the thermal noise generated within the receiver. 15 Interference temperature, expressed in units of Kelvin, can be calculated as the power received by an antenna in watts divided by the associated RF bandwidth in Hertz and a term known as “Boltzman’s constant” (the value of this constant is 1.38 x 10 -23 watt- sec/ K, also note that 1 K = - 272.15° Celsius). Alternatively, interference temperature can be calculated as the power flux density (e. g., microWatts/ m 2 over a bandwidth) multiplied by the antenna capture area in meters squared divided by both the associated RF bandwidth in Hertz and Boltzman’s constant. An “interference temperature density” can also be defined as the interference temperature per unit area, expressed in units of Kelvin per meter squared, and calculated as the interference temperature divided by the effective capture area (aperture) of the receiving antenna. This quantity could be measured for particular frequencies using a reference antenna and, thereafter, would be independent of receiving antenna characteristics. 5 Federal Communications Commission FCC 03- 289 6 would measure the interference temperature at its location and make a transmit/ not transmit decision based on this measurement plus the device’s own contribution of RF energy. If the result of this analysis were below the interference temperature limit set for that location, the device would transmit. Another approach would be for the receive sites of a licensed service to measure the temperature and communicate those measurements to a central site, where the interference temperature profile for the region would be computed. A message could then be broadcast indicating the temperature values over that region and perhaps whether devices would or could not transmit on particular frequencies. This scenario may be appropriate in services such as those involving fixed point- to- point operations where there are relatively few receive sites in a given area. 12. A third more general case, might be to establish a grid of monitoring stations that would continuously examine the RF energy levels in specified bands, process that data to derive interference temperatures, and then broadcast that data to subject transmitters on a dedicated frequency, again perhaps with instructions how to respond. The transmitted temperature data from this monitoring system could also include the frequency and geographic location of the interference temperature measurement( s) and the measurement bandwidth so that an individual device could compute the rise in temperature due to its own contribution and make a decision to transmit. A somewhat simpler version of the monitoring grid concept might be to equip all transceivers on a network operating with interference temperature “thermometers” and GPS receivers so that they could measure and transmit temperature data on a real-time basis. 13. There are several actions that could be taken in the event that a device determines that its transmissions would cause the interference temperature limit to be exceeded. One approach would be to select a different transmitting frequency or, if none were available, to cease transmitting until the RF environment changed to a state in which a transmission would no longer cause an unacceptable temperature level. Another approach would be to reduce the transmitter power and/ or change the direction or shape of the transmit antenna pattern. These capabilities could be implemented by equipping devices with technology such as automatic transmitter power control (ATPC) or with the ability to electrically re- shape antenna patterns. Combining these approaches, a single device could be designed to scan the range of potential operating frequencies before transmitting, compute an estimate of the amount that their operation would add to the interference temperature on each frequency, and select among the frequencies that would allow compliant operation. The device would monitor the interference temperature and if the observed level began approaching or exceeded the limit, could lower its power, switch to another frequency, make an antenna adjustment, or cease transmitting as conditions might warrant. 14. More complex responses than those described above could be taken when considering a coordinated monitoring system. In such a scenario, responses could range from a requirement that all undesired transmitters cease transmitting, to limitations on the number of devices that could operate or the permitted transmitter power, or to restrictions on the operation of unlicensed devices to specific areas. Any of these limitations could be imposed separately, in tandem, and/ or on a priority basis. In cases where devices subject to the temperature cap were not equipped to respond on a real- time basis, actions to ensure the environment remained in compliance with the temperature limit could involve restrictions on sales of additional devices if the temperature approached the limit. Alternatively, a process might be established whereby users registered their devices with an appropriate agent who could then inform them to take actions to reduce the interference temperature if needed. In addition, devices could be built to automatically respond to messages distributed through the local mass media services. Two possible examples include messages that could be embedded in the subsidiary communications authority (SCA) subcarrier transmissions of FM radio stations or within the ancillary data services of broadcast TV signals. Many other variations and options are possible for optimizing the monitoring and response process to avoid exceeding the temperature cap. 6 Federal Communications Commission FCC 03- 289 7 15. Figure 1 shows how the interference temperature limit approach could be beneficial to licensees. 16 This figure shows the signal of a radio station designed to operate out to a range at which the received power approaches the level of the noise floor that existed at the time the system was built. As additional interfering signals appear, the noise floor has increased at various points within the service area, as indicated by the peaks above the original noise floor. 17 As a result, the station’s service reliability and signal coverage have been reduced. The establishment of an interference temperature limit would fix the amount of new interference that the station could experience. That is, the station would be assured of providing service at all locations where its signal exceeded the level of the interference temperature cap. 18 This would assure that the licensed operation would not experience any further degradation or loss of service from new interference, and thereby provide incumbents greater certainty regarding the maximum permissible level of interfering RF energy in the bands in which they operate. Interference temperature limits could also serve as a “worst” case characterization of the RF environment that would provide benchmarks of the operating environment for equipment and system designers. This could aid designers in balancing the numerous technical and economic tradeoffs involved in radio system planning. 16. This approach could also be beneficial for users of unlicensed devices. In areas where the interference temperature would not have been exceeded, opportunities would exist for additional operation by “underlay” transmitters equipped to monitor the interference temperature and to control their operations so that they do not contribute to a condition where the interference temperature cap would be exceeded. Thus spectrum access for unlicensed users and devices would be increased. 17. We also inquire as to the potential costs and benefits of a policy establishing an interference temperature. In particular, we seek comment on the likely costs and benefits to licensees, equipment 16 This figure is taken form the Task Force Report. See Task Force Report, Figures 2 and 3. 17 Note that unlicensed devices can operate successfully across a frequency band occupied by a higher level signal only if the bandwidth occupied by such devices is greater than that of the higher level signal (which is reasonable to assume in the case of direct sequence digital spread spectrum systems and digital transmission systems that have similar spectrum occupancy characteristics). 18 More specifically, stations would be able to provide service at locations where their signal would exceed cumulative levels of interfering signals and noise by some margin above which their receivers need to operate. Such operating margins over noise/ interference levels are common in radio services, and for this reason most stations would not actually be able to provide service out to a range where the level of their signal equals the level of noise plus interference. Conceptually, the required margin could be included in the formulation of the interference temperature limit for a given service and/ or frequency band. Distance from licensed transmitting antenna Licensed Signal New Opportunities for Spectrum Access Original Noise Floor Power at Receiver Figure 1 Interference Temperature Limit Service Range at Original Noise Floor Minimum Service Range with Interference Cap 7 Federal Communications Commission FCC 03- 289 18 systems in their analysis. We also ask that commenting parties include a description of how the appropriate choice for an S/ I threshold might vary with changes in the type of modulation employed by the undesired emissions as well as any supporting test data. 43. For illustrative purposes, combining these assumptions in a link budget analysis indicates that an unlicensed emitter 100 meters away from a 6525- 6700 MHz FS receiver should be able to transmit at a power level of as much as much as 91 dB to 71 dB higher than the level it receives from an FS transmitter without causing harmful interference to the associated FS receiver. 42 Similarly, an unlicensed emitter 100 meters away from a 12.75- 13.25 GHz FS receiver should be able to transmit with a power level of as much as 95 dB to 75 dB higher than that received from the FS transmitter without causing harmful interference to the associated FS receiver. 43 Thus, if the FS signal level at the unlicensed device is -77 dBm, the unlicensed devices should be able to transmit with a minimum signal level of 14 to -6 dBm in the 6525- 6700 MHz band and 18 to -2 dBm in the 12.75- 13.25 GHz band without causing harmful interference to FS reception. This would hold true even if the unlicensed transmitter is operating on a channel currently in use by a fixed station. We seek comment on the merits of this tentative result as well as on the validity of our rationale. Commenters may wish to explore whether other approaches could be used to derive appropriate values for an interference temperature limit in this band. 44. Furthermore, if unlicensed devices were designed to first monitor (e. g., listen- before- talk, or “sniff”) the authorized spectrum to determine the levels of existing RF emissions, they could employ DFS to adjust their frequency of operation to ensure that operation occurs on unoccupied channels. 44 The detection threshold employed within the DFS could be adjusted to accommodate the overhead margins for unlicensed operations calculated above to ensure that the emissions from the unlicensed emitter do not exceed the interference threshold at the fixed receiver. We seek comment on requiring a minimum DFS detection threshold of -64 dBm for unlicensed devices operating at output levels equal to or exceeding 23 dBm and -62 dBm for unlicensed devices operating at output levels below 23 dBm. We further propose that the detection threshold is the received power averaged over 1 millisecond referenced to a 0 dBi antenna. We note that these values generally are consistent with our proposals for DFS employed with UNII operation proposed in the 5470- 5725 MHz band and believe these levels would provide adequate protection to FS operations at 6 and 13 GHz. 45 We seek comment on the merits of and potential problems that might arise from using this real- time monitoring approach. Comments are also sought on alternative methods that could be employed to monitor the RF spectrum signal levels and to control the interference temperature. 45. By employing TPC and DFS and by permitting unlicensed operation at very modest power levels (as indicated above, we envision maximum unlicensed EIRPs possibly in the range of 30 dBm to 42 This result assumes that an unlicensed device receives a signal from the fixed station transmitter with approximately the same free space path loss as the signal path between the fixed station transmitter and receiver. Thus, assuming no variation in other propagation variables, the level of received power at the fixed receiver would be approximately equal to that measured by the unlicensed device with the addition of the gain of the fixed station antenna. That is, antenna off- axis attenuation (- 32 dB) plus typical propagation loss (- 89 dB) plus desired S/ I (30 to 50 dB) produces an unlicensed margin overhead of 91 to 71 dB. We note that this value could be useful in determining the sensitivity of the DFS used with the unlicensed system and seek comment in that regard. 43 Similarly, an antenna off- axis attenuation (- 30 dB) plus typical propagation loss (- 95 dB) plus desired S/ I (30 to 50 dB) produces an unlicensed margin overhead of 95 to 75 dB. We note that this value could be useful in determining the sensitivity of the DFS used with the unlicensed system and seek comment in that regard. 44 The method used to monitor the RF levels and the sensitivity of the monitoring system employed would directly impact how an unlicensed system would adjust its output frequency. Emission levels could be detected by individual unlicensed devices, which would then adjust their output frequencies based on the level of the detected RF emissions, or they could be detected by centralized control stations which would then cause the operating frequencies of their satellite stations to be adjusted. 45 Note that the Commission proposed a shorter averaging duration for UNII devices. 18 Federal Communications Commission FCC 03- 289 19 36 dBm), we believe that sharing between unlicensed devices and these incumbent systems is feasible. We observe that these systems have been able to share in the past by conducting frequency coordination prior to operation. We believe that the use of TPC and DFS can automatically mimic this function, but in real time as opposed to manual human coordination activities. We further observe that the significant power difference between incumbent terrestrial systems and proposed unlicensed devices puts the unlicensed devices at considerably more risk of receiving interference than of causing interference. We request comment on these observations and seek proposals for appropriate technical criteria. Specifically, we seek comment on the proper detection thresholds that should apply for DFS. Should the threshold be referenced to the received power averaged over one millisecond referenced to a 0 dBi antenna? Or should some other reference be used? Detailed technical comments should be submitted to support commenters' positions. Comments also are requested on the bandwidth and time period over which we should require that the spectrum be monitored prior to operation. Also, commenters should provide details regarding how often the spectrum should be monitored after transmission begins. We also request comment whether the TPC capability should be required to reduce power by more than 6 dB below the maximum power? If so, to what level? What are the limits of current technology for TPC? 46. We request comment on these observations and seek proposals for appropriate technical criteria for operation in this band. Specifically, we seek comment on the proper detection thresholds that should apply for DFS. Should the threshold be referenced to the received power averaged over one millisecond referenced to a 0 dBi antenna? Or should some other reference be used? Detailed technical comments should be submitted to support commenters' positions. Comments also are requested on the bandwidth and time period over which we should require that the spectrum be monitored prior to operation. Also, commenters should provide details regarding how often the spectrum should be monitored after transmission begins. We also request comment whether the TPC capability should be required to reduce power by more than 6 dB below the maximum power? If so, to what level? What are the limits of current technology for TPC? 47. General In- band Considerations. We also seek comment on the general in- band technical requirements that would be appropriate for unlicensed operations in the 6525- 6700 MHz and 12.75- 13.25 GHz bands under an interference temperature paradigm. For example, Section 15.402 of the Rules sets forth various limits on the maximum transmit power, the maximum spectral power density, and other related technical limits for unlicensed network information infrastructure (U- NII) devices in various frequency bands. 46 In addition, these rules require systems using directional antennas with a gain greater than 6 dBi required to reduce both the maximum transmit power and the maximum power density. We have found those criteria to be effective, and seek comment on adopting similar technical requirements for unlicensed operations under our interference temperature rules in the 6525- 6700 MHz and 12.75- 13.25 GHz bands. In this regard, we again note that our initial analysis indicates that a reasonable interference temperature limit in this band might support unlicensed operations with maximum transmit powers possibly in the range of 24 dBm to 30 dBm and EIRPs in the range of 30 dBm to 36 dBm. We seek comment on the merit of this tentative conclusion. We also encourage commenters to suggest specific alternative technical limits and to include detailed supporting analysis. Such analysis should minimally include thorough link budget analyses along with discussions of the advantages and disadvantages of various options and alternatives. 48. We request comments on whether any portion of the bands discussed above that are allocated for fixed operation should be excluded from consideration under this proposal and why. For example, is it necessary to preclude unlicensed operation in the 6650- 6675.2 MHz portion of this band to protect radio astronomy operations or can suitable technical standards be developed to ensure that harmful interference is not caused? Is it necessary to preclude unlicensed operation in the 13.15- 13. 2125 GHz band to protect mobile operations or are the proposed standards sufficient to ensure that mobile systems will not receive harmful interference from unlicensed operations? 46 47 C. F. R. § 15. 402. U- NII devices operate on frequencies in the 5. 15- 5. 825 GHz region of the spectrum. 19 Federal Communications Commission FCC 03- 289 21 filed using the Commission's Electronic Comment Filing System (ECFS) or by filing paper copies. See Electronic Filing of Documents in Rulemaking Proceedings, 63 Fed. Reg. 24,121 (1998). 55. Comments filed through the ECFS can be sent as an electronic file via the Internet at . Generally, only one copy of an electronic submission must be filed. If multiple docket or rulemaking numbers appear in the caption of this proceeding, however, commenters must transmit one electronic copy of the comments to each docket or rulemaking number referenced in the caption. In completing the transmittal screen, commenters should include their full name, Postal Service mailing address, and the applicable docket or rulemaking number. Parties may also submit an electronic comment by Internet e- mail. To get filing instructions for e- mail comments, commenters should send an e- mail to ecfs@ fcc. gov, and should include the following words in the body of the message, "get form ." A sample form and directions will be sent in reply. 56. Parties who choose to file by paper must file an original and four copies of each filing. If more than one docket or rulemaking number appears in the caption of this proceeding, commenters must submit two additional copies for each additional docket or rulemaking number. All filings must be sent to the Commission's Secretary, Marlene H. Dortch, Office of the Secretary, Federal Communications Commission, The Portals, 445 Twelfth Street, S. W., Washington, D. C. 20554. 57. Filings can be sent by hand or messenger delivery, by commercial overnight courier, or by first- class or overnight U. S. Postal Service mail (although we continue to experience delays in receiving U. S. Postal Service mail). The Commission's contractor, Natek, Inc., will receive hand- delivered or messenger- delivered paper filings for the Commission's Secretary at 236 Massachusetts Avenue, N. E., Suite 110, Washington, D. C. 20002. The filing hours at this location are 8: 00 a. m. to 7: 00 p. m. All hand deliveries must be held together with rubber bands or fasteners. Any envelopes must be disposed of before entering the building. Commercial overnight mail (other than U. S. Postal Service Express Mail and Priority Mail) must be sent to 9300 East Hampton Drive, Capitol Heights, MD 20743. U. S. Postal Service first- class mail, Express Mail, and Priority Mail should be addressed to 445 12th Street, S. W., Washington, D. C. 20554. All filings must be addressed to the Commission's Secretary, Marlene H. Dortch, Office of the Secretary, Federal Communications Commission. 58. Parties who choose to file by paper should also submit their comments on diskette. Such a submission should be on a 3.5- inch diskette formatted in an IBM compatible format using Microsoft Word or compatible software. The diskette should be accompanied by a cover letter and should be submitted in “read only” mode. The diskette should be clearly labeled with the commenter’s name, proceeding (including the lead docket number, type of pleading (comment or reply comment), date of submission, and the name of the electronic file on the diskette. The label should also include the following phrase "Disk Copy – Not an Original." Each diskette should contain only party’s pleading, preferably in a single electronic file. In addition, commenters must send diskette copies to the Commission’s copy contractor, Qualex International, Portals II, 445 12th Street, SW, Room CY- B402, Washington, DC, 20554. 59. Alternative formats (computer diskette, large print, audio cassette and Braille) are available to persons with disabilities by contacting Brian Millin at (202) 418- 7426, TTY (202) 418- 2555, or via e-mail to Brian. Millin@ fcc. gov. This Notice can also be downloaded at http:// www. fcc. gov/ oet. 60. The proposed action is authorized under Sections 4( i), 301, 302, 303( e), 303( f), 303( r) and 307 of the Communications Act of 1934, as amended, 47 U. S. C. Sections 154( i), 301, 302, 303( e), 303( f), 303( r) and 307. 61. The Commission’s Consumer and Governmental Affairs Bureau, Reference Information Center, SHALL SEND a copy of this Notice, including the IRFA, to the Chief Counsel for Advocacy of the Small Business Administration. 21 Federal Communications Commission FCC 03- 289 22 62. For further information regarding this Notice of Inquiry and Notice of Proposed Rulemaking, contact Gary Thayer, Office of Engineering and Technology, (202) 418- 2290, e- mail gary. thayer@ fcc. gov, or John Reed, Office of Engineering and Technology, (202) 418- 2455, e- mail john. reed@ fcc. gov, or Ahmed Lahjouji, Office of Engineering and Technology, (202) 418- 2061 e- mail ahmed. lahjouji@ fcc. gov. FEDERAL COMMUNICATIONS COMMISSION Marlene H. Dortch Secretary 22 Federal Communications Commission FCC 03- 289 23 Appendix A Initial Regulatory Flexibility Analysis As required by the Regulatory Flexibility Act, 47 the Commission has prepared this Initial Regulatory Flexibility Analysis (IRFA) of the possible significant economic impact on small entities by the policies and rules proposed in this Notice of Proposed Rule Making (“ Notice”). Written public comments are requested on the IRFA. Comments must be identified as responses to the IRFA and must be filed by the deadlines for comments on the Notice provided in paragraph 54 of this item. The Commission shall send a copy of this Notice, including the IRFA, to the Chief Counsel for Advocacy of the Small Business Administration. In addition, the Notice and the IRFA (or summaries thereof) will be published in the Federal Register. 48 A. Need for, and Objectives of, the Proposed Rules. This rulemaking proposal is initiated to obtain comments regarding proposed changes to the regulations for radio frequency devices that do not require a license to operate. The Commission seeks to determine if its standards should be amended to permit the expanded operation of unlicensed devices in the 6525- 6700 MHz and 12.75- 13.25 GHz bands. We believe that it may be necessary to shift our current paradigm for assessing interference from approaches based primarily on transmitter operations towards new approaches that focus on the actual RF environment and interaction between transmitters and receivers, such as the interference temperature metric. In order to begin our exploration of the process that would be involved in a transition to an interference temperature regime, we seek comment on specific technical guidelines in the NPRM portion of our discussion that we believe can be implemented in the near future for selected frequency bands prior to any general implementation of interference temperature limits and real- time adaptation of transmitters to the interference temperature environment. B. Legal Basis. The proposed action is taken pursuant to Sections 4( i), 301, 302, 303( e), 303( f), 303( r), and 307 of the Communications Act of 1934, as amended, 47 U. S. C. Sections 154( i), 301, 302, 303( e), 303( f), 303( r), and 307. C. Description and Estimate of the Number of Small Entities to Which the Proposed Rules Will Apply. The RFA directs agencies to provide a description of, and where feasible, an estimate of the number of small entities that may be affected by the proposed rules, if adopted. 49 The RFA generally defines the term “small entity” as having the same meaning as the terms “small business,” “small organization,” and “small governmental jurisdiction.” 50 In addition, the term “small business” has the same meaning as the term “small business concern” under the Small Business Act. 51 A “small business concern” is one which: (1) is independently owned and operated; (2) is not dominant in its field of 47 See 5 U. S. C. § 603. 48 5 U. S. C. § 603( a). 49 5 U. S. C. § 603( b)( 3). 50 5 U. S. C. § 601( 6). 51 5 U. S. C. § 601( 3) (incorporating by reference the definition of “small- business concern” in the Small Business Act, 15 U. S. C. § 632). Pursuant to 5 U. S. C. § 601( 3), the statutory definition of a small business applies “unless an agency, after consultation with the Office of Advocacy of the Small Business Administration and after opportunity for public comment, establishes one or more definitions of such term which are appropriate to the activities of the agency and publishes such definition( s) in the Federal Register.” 23 Federal Communications Commission FCC 03- 289 24 operation; and (3) satisfies any additional criteria established by the Small Business Administration (SBA). 52 Nationwide, there are approximately 22.4 million small businesses, total, according to the SBA data. 53 A small organization is generally “any not- for- profit enterprise which is independently owned and operated and is not dominant in its field.” 54 Nationwide, as of 1992, there were approximately 275,801 small organizations. 55 The term “small governmental jurisdiction” is defined as “governments of cities, towns, townships, villages, school districts, or special districts, with a population of less than fifty thousand.” 56 As of 1997, there were about 87,453 governmental jurisdictions in the United States. 57 This number includes 39,044 county governments, municipalities, and townships, of which 37,546 (approximately 96. 2%) have populations of fewer than 50,000, and of which 1,498 have populations of 50,000 or more. Thus, we estimate the number of small governmental jurisdictions overall to be 84,098 or fewer. The SBA has developed a small business size standard for wireless firms within the two broad economic census categories of Paging 58 and Cellular and Other Wireless Telecommunications. 59 Under both SBA categories, a wireless business is small if it has 1,500 or fewer employees. For the census category of Paging, Census Bureau data for 1997 show that there were 1320 firms in this category, total, that operated for the entire year. 60 Of this total, 1303 firms had employment of 999 or fewer employees, and an additional 17 firms had employment of 1,000 employees or more. 61 Thus, under this category and associated small business size standard, the majority of firms can be considered small. For the census category Cellular and Other Wireless Telecommunications firms, Census Bureau data for 1997 show that there were 977 firms in this category, total, that operated for the entire year. 62 Of this total, 965 firms had employment of 999 or fewer employees, and an additional 12 firms had employment of 1,000 employees or more. 63 Thus, under this second category and size standard, the majority of firms can, again, be considered small. The SBA has established a small business size standard for Radio and Television Broadcasting and Wireless Communications Equipment Manufacturing. Under this standard, firms are considered small if they 750 or fewer employees. 64 Census Bureau data for 1997 indicate that, for that year, there 52 5 U. S. C. § 632. 53 See SBA, Programs and Services, SBA Pamphlet No. CO- 0028, at pg. 40 (July 2002). 54 5 U. S. C. § 601( 4). 55 U. S. Department of Commerce, Bureau of the Census, 1992 Economic Census, Table 6 (special tabulation of data under contract to the Office of Advocacy of the U. S. Small Business Administration). 56 5 U. S. C. 601( 5). 57 U. S. Census Bureau, Statistical Abstract of the United States: 2000, Section 9, pgs. 299- 300, Tables 490 and 492. 58 13 CFR § 121. 201, NAICS code 513321 (changed to 517211 in October 2002). 59 13 C. F. R. § 121. 201, NAICS code 513322 (changed to 517212 in October 2002). 60 U. S. Census Bureau, 1997 Economic Census, Subject Series: Information, “Employment Size of Firms Subject to Federal Income Tax: 1997,” Table 5, NAICS code 513321 (issued Oct. 2000). 61 Id. The census data do not provide a more precise estimate of the number of firms that have employment of 1, 500 or fewer employees; the largest category provided is “Firms with 1,000 employees or more.” 62 U. S. Census Bureau, 1997 Economic Census, Subject Series: Information, “Employment Size of Firms Subject to Federal Income Tax: 1997,” Table 5, NAICS code 513322 (issued Oct. 2000). 63 Id. The census data do not provide a more precise estimate of the number of firms that have employment of 1, 500 or fewer employees; the largest category provided is “Firms with 1,000 employees or more.” 64 13 C. F. R. § 121.201, NAICS code 334220. 24 Federal Communications Commission FCC 03- 289 25 were a total of 1,215 establishments in this category. 65 Of those, there were 1,150 that had employment under 500, and an additional 37 that had employment of 500 to 999. Thus, under this size standard, the majority of establishments can be considered small. Satellite Telecommunications The SBA has developed a small business size standard for Satellite Telecommunications Carriers, which consists of all such companies having $12.5 million or less in annual receipts. 66 In addition, a second SBA size standard for Other Telecommunications includes “facilities operationally connected with one or more terrestrial communications systems and capable of transmitting telecommunications to or receiving telecommunications from satellite systems,” 67 and also has a size standard of annual receipts of $12.5 million or less. According to Census Bureau data for 1997, there were 324 firms in the category Satellite Telecommunications, total, that operated for the entire year. 68 Of this total, 273 firms had annual receipts of $5 million to $9,999,999 and an additional 24 firms had annual receipts of $10 million to $24,999,990. 69 Thus, under this size standard, the majority of firms can be considered small. In addition, according to Census Bureau data for 1997, there were 439 firms in the category Satellite Telecommunications, total, that operated for the entire year. 70 Of this total, 424 firms had annual receipts of $5 million to $9,999,999 and an additional 6 firms had annual receipts of $10 million to $24,999,990. 71 Thus, under this second size standard, the majority of firms can be considered small. As no party currently is permitted to market or operate equipment under the proposed standards, there will be no immediate impact on any small entities. The Commission does not have an estimated number for the small entities that may currently be capable of producing such products but believes that there are only a few in existence. D. Description of Projected Reporting, Recordkeeping and Other Compliance Requirements for Small Entities. Part 15 transmitters are already required to be authorized under the Commission's certification procedure as a prerequisite to marketing and importation. The reporting and recordkeeping requirements associated with these equipment authorizations would not be changed by the proposals contained in this Notice. These changes to the regulations would permit the introduction of an entirely new category of radio transmitters. E. Steps Taken to Minimize the Significant Economic Impact on Small Entities, and Significant Alternatives Considered. The RFA requires an agency to describe any significant, specifically small business, alternatives that it has considered in reaching its proposed approach, which may include the following four alternatives (among others): “( 1) the establishment of differing compliance or reporting requirements or timetables that take into account the resources available to small entities; (2) the clarification, 65 U. S. Census Bureau, 1977 Economic Census, Industry Series: Manufacturing, “Industry Statistics by Employment Size,” Table 4, NAICS code 334220 (issued August 1999). 66 13 C. F. R. § 121. 201, North American Industry Classification System (NAICS) code 517410 (formerly 513340). 67 Id. NAICS code 517910 (formerly 513390). 68 U. S. Census Bureau, 1997 Economic Census, Subject Series: Information, “Receipt Size of Firms Subject to Federal Income Tax: 1997,” Table 4, NAICS code 517410 (issued Oct. 2000). 69 Id. 70 U. S. Census Bureau, 1997 Economic Census, Subject Series: Information, “Receipt Size of Firms Subject to Federal Income Tax: 1997,” Table 4, NAICS code 517910 (issued Oct. 2000). 71 Id. 25 Federal Communications Commission FCC 03- 289 26 consolidation, or simplification of compliance and reporting requirements under the rule for such small entities; (3) the use of performance rather than design standards; and (4) an exemption from coverage of the rule, or any part thereof, for such small entities.” 72 As noted, in order to begin our exploration of the process that would be involved in a transition to an interference temperature regime, we seek comment on specific technical guidelines in the NPRM portion of our discussion that we believe can be implemented in the near future for selected frequency bands prior to any general implementation of interference temperature limits and real- time adaptation of transmitters to the interference temperature environment. Currently, no party is permitted to market or operate equipment under the proposed standards, so there will be no immediate impact on any small entities. One alternative to our proposal is reflected in our request for comments on whether it is necessary to preclude expanded unlicensed operation in the 650- 6675.2 MHz band to protect radio astronomy operations or whether suitable technical standards can be developed to ensure that interference is not caused. We invite small entities to comment on this alternative. F. Federal Rules that May Duplicate, Overlap, or Conflict with the Proposed Rule. None. 72 5 U. S. C. § 603( c)( 1) – (c)( 4). 26 Federal Communications Commission FCC 03- 289 28 Table 1. Unlicensed devices Power distribution Mobile Devices 10% Duty Cycle Fixed Devices 100 % Duty Cycle EIRP (mw) 50 100 200 1000 2000 4000 Device Distribution % 30 35 20 5 5 5 % simultaneous transmissions at specified EIRP 3.0 3.5 2.0 0.5 5 5 The following sample link budget analyses are based on the assumptions above. Item Units Ext. C Ext. Ku Uplink Frequency Band GHz 6.613 13 Lower Band limits MHz 6525 12750 Upper Band limits MHz 6700 13250 Wavelength m 0.05 0.02 Effective Area Isotrope dBm^ 2 -37.9 -43.7 FSS System Parameters Percent of CONUS in one beam % 75 100 FSS Satellite Uplink Antenna Gain dBi 32.3 31.1 Typical Satellite Receive Temperature K 500 625 FSS Satellite Transmission Gain dB -5.0 5.0 Typical Earth Station Receive Temperature K 90.0 100.0 Equivalent Satellite Link Noise Temperature K 248 2076 Allowable Part 15 Device (Delta T/ T) % 5.0 5.0 Satellite System Parameters Allowable Increase in Eq. Sat. Link Noise Temp K 12.41 103.82 FSS Satellite Transmission Gain dB -5.0 5.0 Allowable Increase in Sat. Noise Temp K 39.2 32.8 Boltzman Constant dBW/ Hz K -228.6 -228.6 Allowable Interference Pwr @ Output of Sat. Ant. dBW/ Hz -212.7 -213.4 FSS Satellite Uplink Antenna Gain dBi 32.3 31.1 Nominal Free Space Loss dB -200.. 3 -206.1 Allowable Interference at Earth Surface dBW/ Hz -44.7 -38.4 Interference Temperature System Parameters Transmit EIRPs from Aggregate Interfering Devices dBW -24.08 -24.08 Assumed Transmit Bandwidth kHz 20000 20000 Part 15 Gain toward Sat dBi 0.0 0.0 Part 15 Power density toward Sat dBW/ Hz -97.1 -97.1 Allowable Interference at Earth Surface dBW/ Hz -44.7 -38.4 Part 15 Power density toward Sat dBW/ Hz -97.1 -97.1 Allowable Emitters per Beam in RLAN BW dB 52.3 58.7 Allowable Emitters per Beam in RLAN BW # 171544 739832 Allowable Emitters Allowable number of emitters/ satellite beam # 171544 739832 Available Bandwidth per satellite beam MHz 175 500 Part 15 Reuse Bandwidths in FSS Band MHz 11.67 25.00 Alternate Polarizations # 2 2 Total number of unlicensed systems within CONUS 53,369,095 369,916,129 28 Federal Communications Commission FCC 03- 289 29 SEPARATE STATEMENT OF CHAIRMAN MICHAEL K. POWELL Re: Establishment of Interference Temperature Metric to Quantify and Manage Interference and to Expand Available Unlicensed Operation in the Fixed, Mobile and Satellite Frequency Bands; ET Docket No. 03- 237. The introduction of a new “interference temperature” model has the potential to tremendously improve radio spectrum management. Rather than assess interference based solely on transmitter operations, the interference temperature model introduced in the Commission’s Spectrum Policy Task Force Report takes into account the cumulative effects of all undesired radio frequency energy. The marketplace demands for spectrum require that we explore new ways to use this resource more efficiently. The Notice of Inquiry seeks comment on various technological factors and the process for managing the transition to a new interference temperature paradigm. The Notice of Proposed Rulemaking seeks comments on technical rules that would establish proper limits and procedures for assessing interference temperature. Moreover, the NPRM proposes to begin experimenting with the interference temperature approach on a limited basis in select frequency bands and recommends imposing restrictions on unlicensed devices that would include limiting the transmitter output power and requirements to use transmit power control (TPC) and dynamic frequency selection (DFS). I fully support consideration of this new approach to interference control and spectrum management. It promises to promote more efficient use of spectrum and encourage new and innovative uses of this important resource for the benefit of the American public. 29 Federal Communications Commission FCC 03- 289 30 SEPARATE STATEMENT OF COMMISSIONER MICHAEL J. COPPS Re: Establishment of an Interference Temperature Metric to Quantify and Manage Interference to Expand Available Unlicensed operation in Certain Fixed, Mobile and Satellite Frequency Bands; ET Docket No. 03- 237. I’m excited to see the beginning of the examination of whether we can put the spectrum temperature concept into practice. As I’ve said before, I think that the idea has great promise, if we use it as a tool to increase the efficiency with which spectrum resources are put to use, as is our statutory responsibility. I hope that commenters will use the NOI to address an issue that is of particular concern to me. While the interference temperature metric may be a good new way to measure interference, we do not have an adequate way to determine what the right interference temperature is for a given band. The only tools we have for this job are the ill- fitting and ill- defined “interference” and “harmful interference” concepts. The inappropriateness and inadequacy of these concepts for the job of prospectively setting interference temperature will make this new metric very hard to use predictably and non- arbitrarily in the real world. So I think that the Commission must work to improve the standard we use to determine permissible levels of interference, whether using the interference temperature metric or some other metric. And I believe that an important side benefit of the added predictability that a better standard would bring is that incumbent spectrum users would be more comfortable with the interference temperature metric. This NOI is the perfect vehicle to start the process. 30 Federal Communications Commission FCC 03- 289 31 SEPARATE STATEMENT OF COMMISSIONER JONATHAN S. ADELSTEIN APPROVING IN PART, CONCURRING IN PART Re: In re Establishment of an Interference Temperature Metric to Quantify and Manage Interference and to Expand Available Unlicensed operation in the Fixed, Mobile and Satellite Frequency Bands; ET Docket No. 03- 237 I commend the Spectrum Policy Task Force and its members for their 2002 report and for bringing to the Commission’s attention a new interference temperature approach to spectrum management. The Task Force noted that the “increasing demand for spectrum- based services and devices are straining longstanding, and outmoded, spectrum policies.” I could not agree more. The reality is that we cannot produce more spectrum. We need to foster a framework for innovation that enables new technologies to come forward to meet demand more efficiently – in both the private and public sectors. Most significantly, the Task Force report offered specific findings and recommendations that have been very useful in stimulating debate in the area of spectrum management. The concept of interference temperature is a particularly significant recommendation, and I very much look forward to a full and vigorous discussion on this challenging issue. I recognize that this is one of the more controversial proposals to come out of the report, but believe that it is entirely appropriate for the Commission to seek comment on new approaches to spectrum management. Whatever the outcome, the deliberation process makes us a better, more informed agency, and I encourage all interested parties to file comments in this proceeding. I have previously noted my belief that the Commission should strive to push the boundaries to accommodate new technologies provided that they do not cause harmful interference. Indeed, a little noticed provision of the Communications Act, Section 157, reads that “It shall be the policy of the United States to encourage the provision of new technologies and services to the public.” If an interference temperature model for quantifying and managing interference can be developed so that it truly prevents real harmful interference and allows for the provision of new technologies and services, then we should encourage its development. I do not know if we are there yet, but I very much look forward to the debate. Finally, while I support the discussion in the item considering the application of the interference temperature approach to unlicensed operations in the 6525- 6700 MHz and 12.75- 13.25 GHz bands, I do not believe that this portion of the item should be styled as a Notice of Proposed Rule Making, as opposed to remaining part of the Notice of Inquiry. I think it is very clear that we are exploring an entirely new concept in the interference temperature model, and it is quite premature to actually discuss proposed rules when the Commission has not even engaged in a preliminary discussion on the interference temperature approach as a whole. I am not sure what the rush is and am not convinced that moving this discussion to the NOI portion of the item somehow holds back our consideration of the interference temperature approach. I think the licensees in these bands deserve better. For this reason, I can only concur to the NPRM portion of this item. 31